You are here: Home / Products / Plastic Pipe Production Line / PE Pipe Production Line / 20-630mm HDPE Pipe Making Machine for Water Supply and Drainage

Share to:

20-630mm HDPE Pipe Making Machine for Water Supply and Drainage

5 0 Reviews

20-630mm HDPE pipe making machine for water supply, drainage and general PE pipe projects. This support page helps buyers compare a wide diameter range before choosing a focused Winsoar PE pipe production line.

Availability:

Quantity:



Inquire Add to Basket

Product Description

20-630mm HDPE Pipe Making Machine for Water Supply and Drainage

Winsoar 20-630mm HDPE Pipe Making Machine for Water Supply and Drainage is a supporting PE pipe extrusion page for buyers comparing wide range HDPE water supply and drainage pipe projects. It helps confirm the practical pipe diameter range, application, extrusion configuration and quotation information before choosing a complete HDPE pipe production solution.

This old PE page is kept as a broad project selection page for buyers comparing multiple pipe diameters in one inquiry. It is useful when the final pipe range is not fixed yet and the buyer needs to understand which core PE line fits the main production plan.

Machine Configuration and Project Selection

Depending on pipe size, the production line can include one or more single screw extruders, PE pipe die head, vacuum calibration tank, cooling tanks, haul-off, cutter and stacker or coiler. The final configuration should be selected according to pipe diameter, SDR, output capacity and application.

Use this page as a selection bridge. Small-diameter projects can compare 16-63mm and 20-110mm core lines, while medium and large projects can compare 75-250mm, 200-400mm and 315-800mm core lines.

Information Needed for Quotation

For a practical quotation, prepare pipe diameter, wall thickness or SDR, raw material type, pipe application, output target, cutting or coiling requirement, workshop voltage and available factory space. These details help Winsoar match the extruder, die head, vacuum calibration, cooling, haul-off, cutter and downstream equipment correctly.

20-630mm rangeHDPE pipewater supplydrainageproject selectionPE extrusion

Related PE Pipe Extrusion Resources

This older PE product page is maintained as a supporting long-tail page. For the main product range, visit the PE Pipe Production Line category.

Useful guides: machines included in a PE pipe production line, PE pipe production line process, PE pipe production line cost and HDPE pipe extrusion line selection guide. Video references: 16-63mm PE video solution, 20-110mm PE video solution, 75-250mm PE video solution.

Features

1. High lineal extrusion speed, big capacity and low power consumption, and achieved multi-layers co-extrusion with 1-5 layers.

2. The copper bush is more wear-resisting and prevent material leakage which can guarantee a stable running of extruder.

3. Material feed via spiral groove, efficient transmission and can effectively reduce back-pressure on extruder.

4. Unique design (barrier, shearing and mixing zone) guarantees a uniformed plasticizing effect, and can reduce the pressure on the screw which guarantees a high speed and stable output capacity.

5. High torque gear box has a smart figuration, compact construction, low noise, high carrying capacity, high transmission efficiency can assure long-time trouble-free operation;

6. PCA(pipe air cooling system) of die head largely increase the extrusion speed and decrease the cooling length of extrusion line, and improve quality of inner pipe surface;

7. Intelligent PLC controlling system with human-friendly interface make the operation easily and conveniently;

8. Chip-free cutter ensuing flat and smooth cutting surface of pipe.

Key Components

SINGLE SCREW EXTRUDER

The single screw extruder is simple in design and inexpensive, so it is widely used. It is suitable for extrusion production of PE, PPR, PERT plastic pipes, sheets and profiles.
MARK LINE CO-EXTRUDER

The extruder is especially widely used on pipe production line to co-extrude pipe mark line. It is specially designed with lower power consumption and takes smaller space.
EXTRUSION DIE

After compaction, melting, mixing and homogenization of PP the subsequent material is pushed to the die by the screw. The extrusion die is the most important part of tube forming.
VACUUM CALIBRATION TANK

Used for shaping and cooling of pipes, it is equipped with a vacuum system, water circulation system, as well as front and rear moving device and left and right, height adjustment manual device, stainless steel box, circulating water spray cooling.
SPRAY COOLING TANK

The cooling water is atomized and sprayed from the special nozzle after being pressed by the water pump, so that the product can be cool to 360 degrees in all directions.
TRACTOR

It is used to continuously and automatically lead out the cooled and hardened pipes from the machine head, and the speed is controlled by frequency conversion.
CUTTING MACHINE

After being controlled by encoder according to the required length, automatic cutting is carried out, the stacker is turned over with a delay, pipes are cutted smoothly without scraps and dust.
AUTOMATIC WINDING MACHINE

This machine is equipped with two reels alternately to ensure the continuity of production. It is suitable for plastic rewinding and packaging, automatic arranging,automatic rewinding, and easy operation.
TURNOVER RACK (OPTIONAL ON REQUEST)

Accept finished products and automatically turn over.

Main Technical Parameter

33D Series Classical Production Line：

Production Line	Diameter Range（mm）	Extruder Type	Max. Capacity （kg/h）	Max. Haul Off Speed（m/min）	Extrusion Power（kw）
WS-63 I	Ф 20-63	SJ65/33	220	12	55
WS-110 I	Ф 20-110	SJ65/33	220	12	55
WS-160 I	Ф 50-160	SJ75/33	400	10	110
WS-250 I	Ф 90-250	SJ90/33	400	6	110
WS-450 I	Ф 160-450	SJ120/33	500	4	160
WS-630 I	Ф 400-630	SJ120/33	850	2	280
WS-800 II	Ф 500-800	SJ120/33	850	2	280
WS-630 I	Ф 315-630	SJ120/33	850	2	355
WS-800 I	Ф 500-800	SJ150/33	1100	1	400

38D Series High Efficient Production Line：

Production Line	Diameter Range（mm)	Extruder Type	Max. Capacity （kg/h）	Max. Haul Off Speed（m/min）	Extrusion Power（kw）
WS-63Ⅱ	Ф 20-63	WSD60/38	320	30	70
WS-110Ⅱ	Ф 20-110	WSD60/38	380	20	90
WS-160Ⅱ	Ф 40-160	WSD60/38	460	15	110
WS-250Ⅱ	Ф 50-250	WSD75/38	600	12	160
WS-450Ⅱ	Ф 110-450	WSD90/38	850	8	250
WS-630Ⅱ	Ф 250-630	WSD90/38	1050	4	280
WS-800Ⅱ	Ф 500-800	WSD120/38	1300	2	355
WS-1200Ⅱ	Ф 710-1200	WSD75/38 WSD90/38	1450	1	160/250
WS-1600Ⅱ	Ф 1000-1600	WSD90/38 WSD90/38	1900	0.6	280/280